TPI 709R Flue Gas Analyzer

Description

The TPI 709R Flue Gas Analyzer is a state of the art, easy to use analyzer designed not only to display and calculate the required readings from a flue but also to cover most of the other measurements associated with combustion.The instrument is ruggedly constructed and comes with a 3 Year unitand 2 Year sensor Guarantee.

The TPI 709R combustion analyzer uses state of the art electrochemical sensors. This sensor technology provides the longest lasting, most accurate and reliable means for performing combustion tests. The sensors in your analyzer will need to be replaced periodically and calibration is recommended once every year. The 709R will remind you when calibration is due by flashing “CAL DUE Err” for three seconds at start up.

Electrochemical sensors by nature are always active. Therefore the time the analyzer is off and not being used must be taken into account when determining sensor life. The sensors in your analyzer are warranted for two years. This warranty does not cover sensors damaged through misuse of the analyzer.

You should keep the batteries of your 709R fresh so power is constantly being supplied to your sensors.

The following guidelines will help prevent damage to your sensors:

• Always use the mini pump filter when testing flue gases.
• Always periodically check and replace the mini pump filter as needed.
• Always make sure the in-line filter / water trap is installed properly.
• Always periodically check and replace the in-line filter as needed.
• Always remove water or condensation from the inside of the in-line filter / water trap assembly prior to performing tests.
• Always use the optional oil filter (p/n A773) when performing tests on oil burning equipment.
• Never over saturate your sensors by performing tests on equipment with gas levels beyond the capability of you analyzer.
• Always keep the A794 water trap / filter assembly clean and replace the filter as necessary. Replacement filter part number is A794F.

The TPI 709R Flue Gas Analyzer comes complete with the following standard accessories:

• TPI 709R Instrument
• Rubber Boot (A765)
• Battery Charger (A766) – 1 each
• Soft Carrying Case (A768)
• Flue Sampling Probe (A770)
• In-Line Filter assembly installed on Flue probe (A794)
• Temperature Probe (GK11M)
• Mini Pump Protection Filter Assembly and spare filters (A763)
• Exhaust Spigot (removable) (A764)
• Instruction Manual

The TPI 709R Flue Gas Analyzer has the following options available:

• Infrared printer (A740)
• Spare In-Line Filter (A794F is a package of 5 filters)

Model 709R Features
Measure CO, O2 & Flue Temperature
Calculate CO2, CO/CO2 Ratio, Efficiency & Excess Air
Dual Input Differential Manometer – Great for performing Standing Pressure or Let By/Tightness Tests
Dual Input Differential Thermometer – Ideal for measuring & recording Flow & Return Temperatures
Ambient CO Analysis
6 Year Warranty* (* subject to annual service being carried out each year by TPI or one of its approved local service centres)
Diagnostic software & technical helpline combine to save time and money on reduced downtime as many of the reported faults can be rectified over the phone keeping you and your instrument working
Unique external water trap filtration system as standard on all kit options preventing loss of downtime or additional costs due to potentially damaged sensors caused by water ingress
10 Fuel options including Wood, Light & Heavy Oil, LPG and Natural Gas
Will not shut off if CO ppm is above 15ppm for increased safety for both the user and the instrument
Unique in-line pump protection filter fitted as standard across all kits preventing loss of downtime or additional costs due to a potentially damaged pump caused by dust/dirt ingress
Protective rubber boot as standard to protect the FGA
Re-Chargeable battery housed in a separate compartment ensuring no heat transfer when using on the mains to affect gas readings
All kits come supplied in a soft carry case to protect not only the FGA but all of your accessories
Capability of sending Live or Stored readings to an optional IR Printer

Specifications

Model 709R Specifications
Instrument
Operating Temperature Range	14°F to +122°F (-10°C to +50°C)
Battery / Batery Life	Rechargeable Ni-MH / > 6 Hours
Charger Input Voltage	115V or 230V : 50/60 Hz AC
Fuels	Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
Pressure Ranges	mbar, kPa & inH2O
Display	Backlit Graphic LCD
Data Storage	50 sets of readings, multiple pages
Time and Date	24 Hour Real Time Clock
Dimensions	7.8” (200mm) x 3.5” (90mm) x 2.4” (60mm)
Weight	500g
Casing	Rubber Boot as Standard
Switch Off	Failsafe
Exhaust	Safety Spigot
Conforms to	EN50379

Flue Temperature Probe
Construction	Pistol Grip with Stainless Steel Shaft
Hose Length	8.2’ (2500mm)
Insertion Length	7.9” (200mm)
‘K’ Type Thermocouple Accuracy	+/- 0.3% of fullscale, +/- 2°F (1°C)
Maximum Temperature	1472°F (800°C)

Gases	Range	Resolution	Accuracy
Oxygen	0-25%	0.1%	+/- 0.3%
Carbon Monoxide	0-10,000 ppm	1 ppm	(<20ppm) +/- 3 ppm (>=100ppm) +/- 5%
Carbon Dioxide (calculated	0-25%	0.1%	Calculated
CO/CO2 Ratio	0-0.999	0.001	+/- 0.3%
Combustion Efficiency	0-100%	0.1%

Selectable Ranges	mbar, kPa and inH2O
Range	– 150 mbar to + 150 mbar
Resolution	0.01 mbar & 0.1 mbar

 

 

 

 

 

 

Buyer Notice
1. About the product
Due to market fluctuations, exchange rate changes, and other factors, product prices and product attributes are for reference only; The specific product requirements are subject to customer requirements, and the price is based on the communicated quotation. All product prices on this website are not considered transaction prices and are for reference only!
2. About Trademark Copyright
All company names, trademarks, logos, product images, product descriptions, product brand names, and trademark copyrights related to this website belong to the corresponding brands; This website is only designed for the convenience of product identification.
Please carefully read the buyer’s instructions to avoid unnecessary disputes.